Skip to content
Get Quote

September 22, 2026

Export Packing and Container Loading for Trolley Orders

Finished trolleys strapped and loaded inside an export container
Finished trolleys strapped and loaded inside an export container.

Two suppliers can quote the same cart at similar unit prices and deliver different landed costs, simply because one thought about packing earlier. Carts are mostly air: how that air is arranged decides container count, freight per unit, damage rates and how long your team spends assembling on arrival.

The three packing routes

Assembled and individually packed

The cart ships as it will be used. Highest freight per unit, lowest handling at destination. Best for distributors who ship onward to end customers, where arriving assembled matters more than freight cost.

Semi-assembled

Typical example: platform trucks with their handles or removable sides detached and bagged with fixings. Often the best compromise – it can cut container volume substantially while keeping assembly to a short, tool-light task.

Knock-down or nested

Maximum container utilisation. suits shelf trolleys, folding cages and any design that can be bolted together rather than welded at every joint. Requires real assembly time at destination, which must be costed honestly.

How much freight does the choice move?

Rough intuition, worth confirming per project:

  • A fully welded cart occupies its full envelope whether empty or loaded, so container count is set by overall dimensions
  • Removing handles on tall carts can change stacking height enough to fit an additional layer
  • A genuinely knock-down design can double or triple units per container compared with assembled
  • Nesting roll cages behaves similarly when the design allows it

The right answer depends on your destination costs. Where labour is expensive relative to freight, assembled wins. Where freight dominates and your team can assemble efficiently, knock-down wins. We quote both when the design supports it.

Protecting the finish in transit

Finish damage is the most common complaint after a first shipment, and it is almost always a packing specification problem rather than a paint problem:

  • Separators between contacting surfaces, not just a single wrap
  • Edge and corner protection wherever cartons meet strapping
  • Caster protection – wheels take abuse in transit and arrive flat-spotted
  • Non-marking wrapping for light-coloured finishes
  • Desiccant where containers will sit in humid ports

Stainless carts need particular attention, which is why they are wrapped individually at source. See our stainless trolleys page for how those are handled.

Container loading discipline

Loading is not just filling space – it is preparation for several weeks at sea:

  • Weight distributed low and evenly, heaviest units near the front bulkhead
  • Blocking and strapping so loads cannot walk during braking and rolling
  • No unsupported spans where the lower layer carries the upper layer’s full weight on one point
  • Photographic record of the load before doors close – invaluable if a claim is ever needed
  • Container and seal numbers recorded against your order documents

What to specify in your RFQ

  1. Packing method: assembled, semi-assembled or knock-down
  2. Whether individual cartons are needed for onward distribution
  3. Labelling: barcodes, part numbers, language markings
  4. Assembly instructions if the cart ships knocked down
  5. Whether you want a loading photograph set before shipment
  6. Destination port, and whether you consolidate with other suppliers

See also our RFQ checklist for the rest of the quotation package.

Calculating landed cost properly

Unit price plus freight is not landed cost. A fair comparison includes:

  • Unit price at your actual quantity
  • Packing cost where charged separately
  • Freight and port charges to your destination
  • Duty and taxes for your market
  • Inland delivery
  • Assembly labour if the cart ships knocked down
  • Expected damage rate and the cost of replacing damaged units
  • Spare wheels and service parts for the first year

Knock-down packing often looks cheapest on freight and loses its advantage on assembly labour, while premium packing looks expensive until damage rates are compared. Ask for both quotations and compare the whole line rather than the headline number.

Receiving: what to do in the first hour

Most freight claims fail on timing rather than merit. On arrival:

  1. Photograph the container and seal before opening, especially if either is damaged
  2. Count units against the packing list before releasing the truck
  3. Photograph any damaged units in place, before anything is moved
  4. Note damage on the delivery document, however minor it looks
  5. Notify the supplier and the forwarder the same day, with photographs

Because shipments are photographed during pre-shipment inspection and during loading, comparing arrival photographs with ours usually settles a claim quickly.

Where Export Orders Actually Get Damaged

Goods rarely arrive damaged because the crate was weak. They arrive damaged because the load moved inside it. A trolley strapped tightly at the top but free at the base will shift on the first long haul, and every corner it touches becomes a scuff or a bent frame. The same applies to powder-coated parts: the coating survives the journey fine if the parts cannot rub against each other, and fails quickly if they can.

That is why we specify packing by what the load does, not by a standard box size. A stackable trolley can often be nested and strapped as a unit; a flat-pack frame needs separated layers and edge protection; a large welded assembly may need a timber crate built around the actual geometry. We photograph the packed load before it leaves so you know what to expect at the other end.

What to Check in the First Hour After Delivery

Unpacking is not the moment to discover a problem three weeks later. Check the outside of the crate for impact marks before opening, photograph anything unusual, and inspect the first few units before the whole shipment is unstrapped. If there is damage, the photographs taken at that moment are what a carrier needs — not a note sent the following week.

We include a packing list that matches the crate, so you can confirm counts and part numbers quickly. If something is missing or marked incorrectly, tell us with the crate number and we will trace it without asking you to unpack everything.

Frequently asked questions

How many units fit in a 40HC container?

It depends entirely on cart dimensions and packing method. Send the drawing and target method and we will calculate it rather than guess.

Can you ship spare wheels in the same container?

Yes, and it is strongly recommended. Spares added to a main shipment cost a small fraction of an emergency air freight order later.

Do you handle consolidation with other suppliers?

We can load alongside goods from other suppliers where you arrange it, and we will coordinate documentation with your forwarder.

Ask for both assembled and knock-down quotations through the contact page and compare landed cost, not unit price.

Laser cutting sheet metal CNC bending Frame welding Batch assembly Powder coating line Quality inspection

Who We Are

Doing Metal is the trolley-focused manufacturing site of Ningbo Fulei Metal Products. Founded in 2016, we build custom metal trolleys in our own workshop — from a drawing, a photo or just a clear idea of the job.

Our Ningbo floor handles the full route in house: laser cutting, CNC bending, welding and riveting, leveling, powder coating, assembly and inspection. One team, one drawing, one accountable partner — from the first sample to a controlled repeat order.

We are an independently audited factory (Bureau Veritas report MIC-ASR263630) and we state our credentials plainly.

Get to know us →

Have a Similar Trolley Project? Send It for Review

Send your trolley type, load capacity, size, wheel requirement, quantity, and drawings or reference photos. Our team will review the structure and reply within 24 hours on business days.

Urgent project? Email gao@doingmetal.com or WhatsApp +86 18158549983.

Related Guides

Read Next on the Same Decisions

Payment Terms and Incoterms for Trolley Orders

Freight terms are where margins quietly disappear. Here is what each common term actually means for a cart order.

Read the guide

Trolley Maintenance and Spare Parts

Carts rarely fail all at once – they degrade. This is the short list of what to inspect and what to keep in stock.

Read the guide

Trolley MOQ and Lead Time Explained

MOQ and lead time are consequences of how a cart is built, not arbitrary numbers. Here is what actually drives both.

Read the guide